CY3670 ftg programming kit cypress semiconductor corporation ? 198 champion court ? san jose , ca 95134-1709 ? 408-943-2600 document number: 38-07410 rev. *a revised january 14, 2008 features supports multiple cypress eprom field programmable clock generators: cy2071af, cy2291f, cy2292f (soic only), cy2907f8, and cy2907f14 separate device specific socket adapters allows quick and easy prototyping compact design for portability easy to use interface: microsoft ? windows ? user friendly cyberclocks ? software for jedec file development kit contents programmer unit serial port cable ac/dc adapter cd containing: cyclocks soft ware, cy_ftg_v2 programmer software, and data sheets for supported devices socket adapters are required and are available separately functional description the CY3670 ftg programming kit enables users with a pc to program cypress eprom field-programmable clock generators quickly and easily. the two setup requirements are a power connection and a serial port connection with the pc, as shown in figure 1 . using cyberclocks ? software, users can configure their parts to the required specifications and generate the corresponding jedec file, which is used for programming. in addition, cyberclocks software provides ppm optimization and power calculations. the jedec file is loaded into the cy_ftg_v2 software that communicates with th e programmer. the cy_ftg_v2 software also has blank-check capabilities and the ability to read, verify, and view the eprom table from a programmed device. this procedure is shown in figure 1 . figure 1. programming procedure on busy cypress ftg programmer - CY3670 programs: cy2071af/cy2291f/cy2292f/ cy2907f8/cy2907f14 bit stream through rs232 serial port device specific adapter cyberclocks (cyclocks) cy_ftg_v2 jedec file [+] feedback
CY3670 document number: 38-07410 rev. *a page 2 of 4 setup hardware the CY3670 ftg programming kit has a very simple setup procedure. as shown in figure 2 , the two connections are the power and the rs232 serial cable to the computer. the programmer must be connected to a pc through a serial port and must receive power through the included ac/dc adapter. the ac/ dc adapter is connected to a standard 110v /220v wall outlet. the final step is to us e the appropriate adapter for the device to be programmed. figure 3 on page 3 is a close up of the socket and shows the correct or ientation for placing the device in the socket. the device must be placed according to the device placement that appears on each adapter. the dots correspond to pin 1 of the device. figure 2. ftg programming kit setup [1] ibm compatible 110v 220v ac/dc adapter text on busy cypress ftg programmer - CY3670 programs: cy2071af/cy2291f/cy2292f/ cy2907f8/cy2907f14 note 1. when plugging the ac/dc adapter into an outlet, be sure to set the 110v/220v switch to the correct setting (110v in the us) a s shown on the power adapter in figure 2 . if no switch exists, it automatically selects between 110v and 220v. [+] feedback
CY3670 document number: 38-07410 rev. *a page 3 of 4 figure 3. device orientation diagram on the adapter software setting up the software is as easy as setting up the hardware. the included cd contains cyclocks, cy_ftg_v2, a readme file, and a folder containing data sheets. the readme file contains information on programming procedures and must be read first. to install cyclocks, the preferred method is to download and install the latest version of cyberclocks software from the cypress website. cyclocks is now a subset of cyberclocks. users must be aware that cyberclocks is not the same as the cyberclocks online w eb-based application. [2] the cy_ftg_v2 software does not require installation. copy the cy_ftg_v2 directory from the cd to the desired location on your machine. a com port and baud rate must be set when the cy_ftg_v2 is first run. the latest version of this software may be located by searching the cypress website http://www.cypress.com for ?CY3670?. adapters the CY3670 kit does not include any socket adapters. the necessary adapters may be ordered from cypress semiconductor. to order an adapter, contact your local cypress sales office or representative, or visit the online store at www.cypress.com. the section ordering information on page 3 lists the available adapters and their corresponding devices. electrical characteristics cy2292f pin 1 cy2071af pin 1 socket cy3096 cy309x item part description cypress part number characteristics 1 cypress ftg programmer CY3670 voltage 12vdc. supports cy2292f, cy2291f, cy2071af, cy2907f8, and cy290714 through adapters purchased separately. 2 serial cable ? ul approved standard 9 pin serial cable. (rs232: one end male /other end female) 80 c, 300v, vw-1, 28awg, awm i/ii. 3 power adapter ? input: 110v/220v ac, 60/50 hz the CY3670 programmer draws from 100 to 150ma. at this load, the adapter supplies 12v, which is the required voltage. the rated output: 9v dc is specified for 1a load (this adapter does not have a voltage regulator.) ordering information ordering code [2] description CY3670 ftg programmer kit cy3093 socket adapter for cy2291f cy3095 socket adapter for cy2292f (soic package only) cy3096 socket adapter for cy2071af cy3097 socket adapter for cy2907f8 cy3098 socket adapter for cy2907f14 note 2. be sure to check for cyberclocks updates at http://www.cypress.com/cyberclocks [+] feedback
document number: 38-07410 rev. *a revised january 14, 2008 page 4 of 4 microsoft and windows are registered trad emarks of microsoft corporation. cyclocks and cyberclocks are trademarks of cypress se miconductor. all product and company names mentioned in this document are the trademarks of their respective holders. CY3670 ? cypress semiconductor corporation, 2002-2008. the information contained herein is subject to change without notice. cypress s emiconductor corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a cypress product. nor does it convey or imply any license under patent or other rights. cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement wi th cypress. furthermore, cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. the inclusion of cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies cypress against all charges. any source code (software and/or firmware) is owned by cypress semiconductor corporation (cypress) and is protected by and subj ect to worldwide patent protection (united states and foreign), united states copyright laws and internatio nal treaty provisions. cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the cypress source code and derivative works for the sole purpose of creating custom software and or firmware in su pport of licensee product to be used only in conjunction with a cypress integrated circuit as specified in the applicable agreement. any reproduction, modification, translation, compilation, or repre sentation of this source code except as specified above is prohibited without the express written permission of cypress. disclaimer: cypress makes no warranty of any kind, express or implied, with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. cypress reserves the right to make changes without further notice to t he materials described herein. cypress does not assume any liability arising out of the application or use of any product or circuit described herein. cypress does not authori ze its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. the inclusion of cypress? prod uct in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies cypress against all charges. use may be limited by and subject to the applicable cypress software license agreement. document history page document title: CY3670 ftg programming kit document number: 38-07410 rev. ecn no. issue date orig. of change description of change new 114457 07/24/02 ckn new datasheet *a 1938667 see ecn kvm/aesa change title from ?CY3670 ptg programming kit? to ?CY3670 ftg programming kit? for consistency change document status from preliminary to final remove references to socket adapter cy3099 and support for cy2292fz (tssop package) clarify that the CY3670 kit does not include any socket adapters correct obsolete website urls correct software references: previously referred to cyclocks but not cyberclocks [+] feedback
|
